Swimming Pool Acid Wash Do's and Dont's

Like anything, an acid wash has a learning curve and I suggest you team up with another pool pro as a helper before setting out on your own to do an acid wash. You also need to be aware of your city's codes on draining a pool and also be aware of a few big cautions which I will unpack below such as don’t drain a pool directly into the street, don’t drain a pool if the air temperature is 90 degrees or hotter and leave it empty for more than a day and don’t drain the water directly into the dirt or grass directly next to the pool.

Chapter Marks:
00:00 What to expect
01:22 What can be Acid Washed?
02:00 The Don'ts
11:43 Acid Mixture
15:30 Power Sanding the Surface
17:47 Bead Blast a Pebble Pool
20:08 Clean the filter
20:26 Where is the Sewer line?

If the plaster has cracks and chips in it already, and Acid Wash will make things worse. There will be more chipping and bigger chunks of plaster will start to come off once the pool is refilled. A Pebble Tec pool with pebbles coming off or cracks is a sign that an Acid Wash should not be done. This will make the Pebble Tec surface worse and not better.

You also want to be careful not to drain a pool down if the outside air temperature is above 90 degrees. This can also cause the plaster to chip, but not until you refill the pool. Sun exposure at that temperature will weaken the old plaster and the chipping will appear over time. So it would be optimal to schedule the Acid Wash offseason when the weather is milder.

The Acid Wash mix is the most important element of Acid Wash. Here are the products that you need for a successful acid wash. You will need 31.45% Muriatic Acid mixed with water in a 2 to 1 water to acid mix. Bio-Dex Plaster White ‘n Brite to help thicken up the acid solution so that it runs smoothly down the walls of the pool and to reduce the acid fumes. Bio-Dex AquaDex 50 Stain-Off which helps to remove iron and another metal staining from the surface. If you use this Acid Wash mix you will have great results and the plaster or Pebble Tec will look as good as new!

You can prep the pool to remove some of the calcium build up on the tile with the Bio-Dex Protect-All-Supreme which will require you to raise the water level over the pool tile calcium line, pour in 1 or 2 gallons of the Protect-All-Supreme into the pool, and then run the pool for 24-48 hours.

Here are the detailed instructions from Bio-Dex on how to do an Acid Wash the Bio-Dex way:
https://drive.google.com/open?id=1DySSQfRRvUU00yqGC09EQvYVsrPkZV1y

Acid Wash Tips:
Always wear protective gear as the fumes and acid are hazardous.

You also, do not want to drain a pool when the water table is high-, if you have 3-6 inches of rain coming your way, do not drain a pool as it could potentially pop out. You also don’t want to drain the water into an area around the pool. The ground can absorb the water, and this can also create a situation where the pool can pop out. This is rare and something you don’t need to worry about. You of course only want to Acid Wash a plaster of Pebble Tec pool and never acid wash a Fiberglass pool.

If the pool has heavy calcium staining on the surface, organic and metal staining can be trapped under the calcium. You can check for calcium before draining the pool simply by feeling the pool surface.

If it feels very rough like sandpaper, chances are there is a lot of calcium build-up on the surface. Before doing the Acid Wash you will need to power sand the pool surface. You can rent a power sander at Home Depot and then sand down the entire pool surface before the Acid Wash. During Acid Wash if you notice the staining is not lifting off, take some sandpaper and rub the area. Then pour the acid mix over the area again. If the stain lifts then you know there is a coat of calcium build-up on the surface and you will have to power sand the entire pool.

Never use just straight acid on the surface. This will etch and damage the surface and will create streaking of the plaster. If the stain is not coming off calcium is probably the issue and not the acid mix.

The basin in the deep end is very critical. I always add Soda Ash to the basin and leave the Sump Pump (Submersible Pump) running so that the acid running off the walls does not pool up and stain the plaster. If this happens, once the pool is filled you will see a discolored ring around the deep end of the pool. So, keep the basin filled with Soda Ash or Baking Soda to neutralize the acid as it runs into the deep end basin and out through the Sump Pump.

If you follow these tips your Acid Wash will turn out great and your pool will have a new lease on life.

Visit my Website: http://www.swimmingpoollearning.com/
eBook: https://www.swimmingpoollearning.com/swimming-pool-care-ebook
YouTube Video Index: http://poolmandave.blogspot.com/2014/03/swimming-pool-tips-reviews-how-to-video.html – A list of all of my videos.
Blogger: http://poolmandave.blogspot.com/